Used 10 BBL 3 Vessel Steam Brewhouse, CLT, HLT, Boiler, Glycol Chiller, & Grist Mill

Price: $122,000

Key System Features:
Full stainless steel work platform w safety railing and non-slip substrate Stainless steel brewhouse, piping, valves, clamps and fittings
Sanitary Single Stage Heat Exchanger 100 sq. ft. surface area

Control System
– Digital control panel
– Automatic temperature controls
– Variable speed drives for brew house motors/pumps – Manual fluid valves

Mash & Lauter Tun
– Stainless steel grist hydrator w/ hot & cold hydration inlet
– Upper and lower steam jackets
– Fully insulated vessel
– Stainless Steel Cladding
– SS CIP Sprayball with 360° of coverage.
– Interior Light
– Top manway (tempered glass)
– Sparge ring assembly
– Side Manway for automatic spent grain out process
– Automatic variable speed rake system and spent grain plow

Brew Kettle/WP
– Upper and lower steam jackets
– Top ventway (Ductwork to outside not included) – Fully insulated vessel
– Stainless Steel Cladding
– SS CIP Sprayball with 360° of coverage.
– Top manway (tempered glass)
– Interior light

Wort Pumps
– Waukesha/Baldor Stainless Steel Wash-down Pump – VFD Speed Control

Whirlpool Pump
– Waukesha/Baldor Stainless Steel Wash-down Pump – VFD Speed Cont

External Wort Grant.
Features:
– Stainless steel cylinder 10″ dia, 36″ tall
– Total wort volume approx 11 gallons
– Total height 46″ with tri-pod legs
– Hinged stainless steel cover
– Sight level glass
– Isolation valves
– Drain valve
– All 1.5″ sanitary tri-clamp connections

Wort Aeration Assembly

Features:
– Stainless steel pipe assembly
– Aeration stone
– O2 1/4″ NPT ball valve O2 disconnect – 1.5″ Sanitary tri-clamp connections
– Built in 4″ sight glass

Two Stage Heat Exchanger Upgrade

Features:
– Two stage heat exchanger upgrade
5 Ton Commercial Water/Glycol Chiller System
System Features:

– To provide approximately 60,000 Btu/hr. of cooling with 50.F leaving fluid temperature with an ambient temperature of 95.F.
– Low Ambient Kit Good to -20F

Controls
– Electronic temperature controller with constant (set point & process) temperature readout on standard units,
actual and programmed temperature LED readout.

Refrigeration Components
– Efficient scroll compressors, sight glass/moisture indicators, balance port expansion valves, filter drier, service
valves, stainless steel brazed plate evaporator, fan cycling head pressure controls, and low ambient controls.

Process Fluid Components
– Stainless steel centrifugal pump, bronze “Y” strainer with 20 mesh stainless steel screen, insulated stainless steel
reservoir with shoe box lid.

Safety Controls
– High/low pressure safeties, low water flow switch, internal and/or thermal overloads for compressor and fan
motors, safety fuses for pump.

Construction
– Welded steel powder coated frame and cabinet, copper piping connections.

Fluid Connections
– 1″ NPT Male Outlet
– 3/4″ NPT Female Inlet

Compressor
– 5 H.P. Hermetic Scroll (Copeland Brand)

Evaporator
– Stanless steel / Copper brazed

Condenser Fan – 3500 CFM

PROCESS SUPPLY PUMP – Standard Pump – 1 H.P.
– Output 30gpm @ 30psi

Reservoir
– 25 GALLON – 304ss – Reservoir Insulated

Condenser Coil
– Air Cooled
– Designed for industrial use – Copper Tube, Aluminim Fin

Power Requirements
– 208/230 VOLT – 3 Ph – Minimum service required – 27 amps – Or 460 VOLT 3 Ph – Minimum service required – 15 amps

Unit Dimensions
– 44″ L x 32″ W x 59-1/2″ H

Unit Weight
– 500lbs Empty
 

Grist Mill 1,200 lbs/hr
Features:

* 6×6 Single Pair Malt Mill
* Designed specifically for the milling of malt for use in breweries
* WEG 1800 RPM 3-Phase XP Motor
* Magnet, Brew
* 25″ Brew mill stand with 45 degree flex auger boot attachment unloader piece
* Optional Stairs Available for $927

– High yield extract efficiencies= 88-95% – Save 4 – 6% on grain cost
– 100% dust tight
– 6 x 6 Dual rollers

– Heavy duty construction
– 1,200lbs/hr output
– Motor starter with thermal overload
– Explosion proof motor available but not included.
10 BBL Cold Liquor Tank

Features:
Glycol Cooled Cold Water Tank 10bbl volume
– Stainless steel (304) sanitary construction
– 100% TIG welded
– 4 heavy duty stainless steel legs with adjustable height and leveling footpads – Interior shell: 304 stainless steel, thickness 11 gauge (3mm)
– 1.5″ (38.1mm) Tri-clamp sanitary fittings (2.0 (50.8mm) on relief valve)
– Thermowell
– Sample valve
– Lifting lugs
– Top manway
– CIP arm and spray ball 360° coverage.
– Easy clean slide over pipe spray ball connection with keeper pin.
– Visual level sight glass
– Dual zone cooling jacket with glycol inlets and outlet
20 BBL Hot Liquor Tank

Features:
Hot Water Tank 20bbl volume
– 304 Stainless Steel
– Top Manway
– Steam Jacketed and insulated
– Insulation
– Cladding
– Stainless Pipes, Valves and Fittings

Share this listing

Q & A

log in or create an account to view Question & Answers

Contact Info & More

Please login to view contact info

Login/Register